painting and decorating is repair-painting and decorating repair and painting and decorating repair and furnish furnish and repair

the Device of transformed partitions (ch. 2)

the Easy soft partition can be made of film materials on a fabric basis, wooden bruskov and rollers. It is intended for premises in height of 2,6-2,7 m. Optimum length of such partition - no more than 3 m. For the partition device, first of all, mark places of its installation. Then prepare a bar section 55X40 mm in the length equal to distance between walls, drill in it on all length of an aperture in diameter of 2 mm with step of 600-800 mm. Then put it to a ceiling along a line of a marking and shilom or a nail mark installation sites djubelej or stoppers. After fastening of a bar from its both parties screws with step of 600-800 mm krepjat rejki section 25XI00 mm in which bottom part two metal corners are fixed. The length of corners should be shorter than a bar that will provide possibility of installation of rollers on 60-65 mm. Between regiments of corners there should be a backlash in 4-5 mm on which the plate connecting rollers with a partition (fig. 45 will move ahead).

60X70 mm make the Plate in the size of a piece of textolite, aluminium or there were in the thickness of 2-3 mm. In its top part on distance of 15 mm from edges bore through two apertures in diameter of 5-6 mm. Distance centre to centre apertures - 30 mm. In these apertures on an axis two pairs rollers in diameter of 25-28 mm are fixed. Rollers can be picked up and bolshego diameter, however thus it is necessary to increase width of lateral laths and, accordingly, more low to lower corners-directing for sliding of rollers. Two lugs from kapron (toddlers) Here attach. They will provide smooth movement of vertical laths at opening and partition closing.

the Easy soft partition: and - a partition general view; - knots and partition details; 1 - screws; 2 - an imitation leather; 3 - a leading lath; 4 - rejki 30Х (10-15) mm

a Fig. 45. An easy soft partition :
And - a partition general view; - knots and partition details;
1 - screws; 2 - an imitation leather; 3 - a leading lath; 4 - rejki 30Х (10-15) mm

By means of two corners 25X25Х60 mm attach the Bottom part of a plate to a leading vertical lath of a partition.

For a skeleton it is necessary to prepare rejki section 30Х (10-15) mm (their quantity depends on length of a partition). At calculation it is necessary to consider that rejki will be connected among themselves in pairs and are located from each other at the closed partition on distance of 140-150 mm. Besides, by quantity coupled reek it is necessary to cut a strip of thin bumazhno-layered plastic in the size 25X70 mm.

The Leading vertical lath do of a bar by section 55X85 mm or stick together from two-three laths of smaller section. On one of lateral sides do a crest providing a dense adjunction of a partition to a wall, having a corresponding groove.

Except the listed materials, it is necessary to prepare also a panel viniliskozhi in the width 450-470 mm and the length equal to height of a partition. The bottom and top edges of panels are recommended to be processed.

Viniliskozhu can be connected to thin foam rubber by means of glue or having stitched on the sewing-machine all surface in the form of squares, rhombuses.

Collect a partition so. To the top end face of a leading vertical lath screws attach a plate with rollers. After that a lath in horizontal position by a crest downwards temporarily fix on a table or to a floor. Then take a panel, stack its middle on a lath and beat to it small nails with a wide hat on all length with step of 200-250 mm. Rejku section 30Х (Ю-15) mm stack from above and attach screws to a leading lath. After that wrap panel edges on length, impose them on rejku and fix nails. In the top part rejki screws the in length of 8-9 mm attach a plate with toddlers and after that stack following rejku and fix its screws. Such operations repeat with all panels and rejkami. On last rejke which should adjoin a wall, place three metal plates in the size 80X50 mm with apertures for fastening to stoppers or djubeljam in a wall.

Sliding doors on the top suspension bracket: and - a door general view; - corners and details of the top suspension bracket and bottom directing: 1 - screws; 2 - a bar 50X55 mm; 2 - eaves; 4 - rollers; S - a corner (18-20) H (18-20) mm; 6 - a door cloth; 7 - a corner 25X25 mm; 8 - a rubber strip

a Fig. 46. Sliding doors on the top suspension bracket :
And - a door general view; - corners and details of the top suspension bracket and bottom directing: 1 - screws; 2 - a bar 50X55 mm; 2 - eaves; 4 - rollers; 6 - a corner (18-20) H (18-20) mm; 6 - a door cloth; 7 - a corner 25X25 mm; 8 - a rubber strip

The partition Collected thus bring to an aperture and by means of rollers on the directing hang a leading vertical lath. For simplification of installation all other part of a partition turn off, then one for another get in directing toddlers with rejkami and panels viniliskozhi. When all partition will be hung, last lath attach to a wall to in advance established stoppers. Fastening places cover nashchelnikami. All wooden details varnish.

Sliding doors also can be made on the top suspension bracket. However in this case cloths of doors should be facilitated - frame with a covering tonkolistovymi materials. A plate with rollers and fixing corners make same, as well as for a soft partition, however the width of the bottom shelves of fixing corners should make 15 mm because a thickness of a door of 40 mm. For fastening directing it is necessary to prepare three steel plates in the sizes 130X60X3 mm in which on distance of 7-8 mm from the top and bottom edges bore through on two apertures under screws in length of 50-60 mm. Plates place on a wooden bar section 50X55 mm so that the upper edge of plates with an aperture acted from a bar plane on 15 mm. On distance of 5 mm from a bar fix a corner with regiments 25X25 mm. The design prepared thus consisting of a bar, corner and plates connecting them screws attach to stoppers or djubeljam, established in advance over a doorway. The length of a bar and corners depends on width of an aperture: if the door odnopolnaja, length of a bar from the directing has to be equal to double width of an aperture.

Three other plates in the size 65X60 mm fix also to a corner with regiments 25X25 mm, and then to a bar so that the corner was opposite before the established corner with a backlash between the bottom regiments of 5 mm. To top obvjazke a door cloth attach plates with rollers, and in bottom obvjazke choose a groove depth 22 and width 4-5 mm. To a floor, in a threshold installation site, attach a corner with regiments (18-20) H (18-20) mm which, entering into a groove, will give doors necessary stability. Having finished all spadework, a cloth bring to directing over doorways and get a plate with rollers in a groove between corners, and the bottom groove of a cloth nasazhivajut on a corner placed on a floor. After approbation of opening and door closing, to brusku attach the eaves which width should provide cover directing and knot of fastening of cloths to a plate (fig. 46).