painting and decorating is repair-painting and decorating repair and painting and decorating repair and furnish furnish and repair

Facing drevesnostruzhechnymi plates

Brick and stone walls revet drevesnostruzhechnymi with plates on the wooden skeleton attached to a surface of a wall after proveshivanija how it became at facing gipsokartonnymi sheets. It is possible to revet the concrete, plaster and plastered surfaces drevesnostruzhechnymi with plates, fixing their or fixing elements directly to the stoppers established in a wall.

For facing of a lobby it is better to use drevesnostruzhechnye the plates covered with an interline interval. It is possible to revet not trimmed plates with an interline interval (the section " the Device of elements юсюЁѕфютрэш " see;). Them also it is possible to paste over polyvinyl-hloridnymi with films or the paper wall-paper simulating various breeds of wood, and also to fit or paste over with films on a fabric basis. The obverse surface of the plates which have been pasted over with paper wall-paper, it is necessary to cover in some layers nitrocellulose, and then oil or pentaftalevym with a varnish.

Lateral sides drevesnostruzhechnyh plates are necessary for connecting how it is shown on fig. 37. It is better, when to lateral sides of plates attach wooden rejki. However it is possible to do grooves and in DSP, without reek.

In the first variant the device of grooves on all lateral sides of plates is provided. In this case plates krepjat nails or screws. Then into a groove it is inserted shponka from wooden rejki by section 30X4 mm or a metal strip, and on it the following panel which is kept by a groove for shponku approaches.

The Second variant of connection provides in one party of a plate a crest, and another - a groove. The plate with a groove is fixed the same as and in a case described earlier, and with a crest is put to a skeleton and hammer blows on a panel end face (through a lining from a wooden bar) is got by a crest in a groove of the previous panel. The party with a crest is attached to a skeleton by a nail.

In the third variant on lateral sides choose only a quarter. Plates krepjat to a wooden skeleton nails; after facing end in a groove formed on joints, insert wooden apportions, which krepjat on glue or on screws. The quarter can to be chosen, and krepit plates to a wall by means of wooden apportions (fig. 37. For prodelyvanija apertures under screws, and also for fastening of an apportion by nails in hard-to-reach spots it is possible to take advantage of the simple adaptation which consists of a steel core and a metal tube into which the nail is inserted.

Drevesnostruzhechnye of a plate is possible krepit to a wooden skeleton and without grooves and crests. It is especially important at the Further furnish by films on a fabric basis. Such plates krepjat to a skeleton by means of the plywood overlays attached to the back party of the panel on screws, also mount closely to each other or widened rustom which is filled with wooden apportions.

Ways of connection drevesnostruzhechnyh plates: and - connection not shponkah; - connection "ярч - уЁхсхэі": 1 - wooden framing rejka; 2 - shponka; 3 - a wooden skeleton; 4 - a nail; 5 - DSP; in - facing DSP with fastening by means of apportions: a 1-wall; 2 - a wooden bar; 3 - DSP; 4 - an apportion; 5 - a nail

a Fig. 37. Ways of connection drevesnostruzhechnyh plates :
And - connection not shponkah; - connection "ярч - уЁхсхэі": 1 - wooden framing rejka; 2 - shponka; 3 - a wooden skeleton; 4 - a nail; 5 - DSP; in - facing DSP with fastening by means of apportions: a 1-wall; 2 - a wooden bar; 3 - DSP; 4 - an apportion; 5 - a nail